Enerpac SC-3 User Manual download pdf

Repair Parts Sheets for this product are available from the Enerpac

web site at www.enerpac.com, or from your nearest Authorized

Enerpac Service Center or Enerpac Sales office.

1.0 IMPORTANT RECEIVING INSTRUCTIONS

Visually inspect all components for shipping damage. Shipping

damage is not covered by warranty. If shipping damage is found,

notify carrier at once. The carrier is responsible for all repair and

replacement costs resulting from damage in shipment.

SAFETY FIRST

2.0 SAFETY ISSUES

Read all instructions, warnings and cautions

carefully. Follow all safety precautions to

avoid personal injury or property damage

during system operation. Enerpac cannot be responsible for

damage or injury resulting from unsafe product use, lack of

maintenance or incorrect product and/or system operation.

Contact Enerpac when in doubt as to the safety precautions and

operations. If you have never been trained on high-pressure

hydraulic safety, consult your distribution or service center for a

free Enerpac Hydraulic safety course.

Failure to comply with the following cautions and warnings could

cause equipment damage and personal injury.

A CAUTION is used to indicate correct operating or maintenance

procedures and practices to prevent damage to, or destruction of

equipment or other property.

A WARNING indicates a potential danger that requires correct

procedures or practices to avoid personal injury.

A DANGER is only used when your action or lack of action may

cause serious injury or even death.

WARNING: Wear proper personal protective gear when

operating hydraulic equipment.

WARNING: Stay clear of loads supported by

hydraulics. A cylinder, when used as a load lifting device,

should never be used as a load holding device. After the

load has been raised or lowered, it must always be blocked

mechanically.

DANGER: To avoid personal injury keep hands and

feet away from cylinder and workpiece during

operation.

WARNING: Do not exceed equipment ratings. Never

attempt to lift a load weighing more than the capacity of

the cylinder. Overloading causes equipment failure and

possible personal injury. The cylinders are designed for a max.

pressure of 350 bar [5,000 psi]. Do not connect a jack or cylinder

to a pump with a higher pressure rating.

Never set the relief valve to a higher pressure than the

maximum rated pressure of the pump. Higher settings

may result in equipment damage and/or personal injury.

WARNING: The

system operating

pressure must not

exceed the pressure rating of

the lowest rated component

in the system. Install

pressure gauges in the

system to monitor operating

pressure. It is your window

to what is happening in the

system.

CAUTION: Avoid

damaging hydraulic

hose. Avoid sharp

bends and kinks when

routing hydraulic hoses.

Using a bent or kinked hose

will cause severe back-

pressure. Sharp bends and

kinks will internally damage

the hose leading to premature hose failure.

Do not drop heavy objects on hose. A sharp impact may

cause internal damage to hose wire strands. Applying

pressure to a damaged hose may cause it to rupture.

IMPORTANT: Do not lift hydraulic equipment by the

hoses or swivel couplers. Use the carrying handle or other

means of safe transport.

CAUTION: Keep hydraulic equipment away from

flames and heat. Excessive heat will soften packings and

seals, resulting in fluid leaks. Heat also weakens hose

materials and packings. For optimum performance do not expose

equipment to temperatures of 65 °C [150 °F] or higher. Protect

hoses and cylinders from weld spatter.

DANGER: Do not handle pressurized hoses. Escaping

oil under pressure can penetrate the skin, causing serious

injury. If oil is injected under the skin, see a doctor

immediately.

WARNING: Only use hydraulic cylinders in a coupled

system. Never use a cylinder with unconnected couplers. If

the cylinder becomes extremely overloaded, components

can fail catastrophically causing severe personal injury.

IMPORTANT: Hydraulic equipment must only be serviced

by a qualified hydraulic technician. For repair service,

contact the Authorized ENERPAC Service Center in your

area. To protect your warranty, use only ENERPAC oil.

WARNING: Immediately replace worn or damaged parts by

genuine ENERPAC parts. Standard grade parts will break

causing personal injury and property damage. ENERPAC

parts are designed to fit properly and withstand high loads.

3.0 PRODUCT DESCRIPTION

The SC-3 swing cylinders rotate 90° at the first portion of the

stroke, continuing without rotation for the final clamping stroke.

Instruction Sheet

SC-3

Swing Cylinder

L1682 Rev. O 02/03

1 2

Summary of Contents

Page 1 - Swing Cylinder

Repair Parts Sheets for this product are available from the Enerpacweb site at www.enerpac.com, or from your nearest AuthorizedEnerpac Service Center

Page 2 - Enerpac Worldwide Locations

Cylinders can be changed from right swing to left swing or straightpull by loosening the side plug and then rotating the plunger to thedesired positio

Comments to this Manuals

No comments

Enerpac SC-3 User Manual

Browse online or download User Manual for Tools Enerpac SC-3. Enerpac SC-3 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Tools Enerpac SC-3